ETL Systems

10MHz GENUS StingRay RF over Fibre module With ultra low phase noise and 10km nominal range. StingRay Broadband Transmit and Receive RF Over Fibre modules to fit Genus 2U chassis. The transmit module can provide LNB power 13/18VDC, 22kHz tone up to 500 mA. When fitted with a 10 MHz distributing module the TX/RX module can inject an external or internal 10 MHz tone onto the broadband feed.

The IRT 20W-65W BUC / SSPB / SSPA powered by GaN technology super compact series are revolutionary in size, weight and power density. This series offers superior performance in an extremely compact package that can fit in your palm! Weighing at only 2KG, our feature-rich GaN unit is exceptionally powerful for its size: up to 65W Psat. IRT GaN super compact features best in class RF characteristics, embedded WG circulator, extensive monitor and control capabilities enabled via Ethernet, Serial and/or Analog Interfaces. This series remarkably small size and low power consumption results in better heat extraction that leads to overall system size and cost reduction making it the ideal candidate for portable, mobile and VSAT on the move applications. Its small size and weight allows direct feed horn mounting, which makes it a most economical solution for fixed VSAT applications. Options Internal / Autosense 10Mhz reference True RMS detector Antenna Mounting kit Features Up to 65W PSAT Output Power in this supercompact light weight package 14x15x9.5cms Only 290W power consumption at 60W output 200W power consumption at 3dB back off Switchable LO – Standard and Extended Ku-Band in one unit RF overdrive protection Status LED Superior RF performance: Phase noise 6dB better than IESS308/309 High Linearity Spurious below-60dBc Wide dynamic range of Gain Control Output power measurement Built in WG Circulator provides full output VSWR Protection Configuration via RS-232 serial console, packet protocol RS-485 and User friendly Ethernet HTTP based GUI and SNMP support Redundancy Ready – No external redundancy controller required Field Replaceable Fans Field upgradable software

Alto L-band Redundant Amplifier Module with low noise, high linearity, variable gain and slope control The L-band redundant low noise amplifier module is designed to work in the Genus 1U redundant chassis range, operating over 850-2150 MHz. The module has low noise, high linearity, with variable gain and slope control. Chassis Specification Dimensions/Weight/Colour 1U high x 550mm deep x 19″ wide / Capacity 17 module slots. Note: Actual modules may require >1 slot. Refer to required module spec table. Temperature Operating: 0˚C to +45˚C Storage: -20˚C to +75˚C Location/Humidity/Altitude Indoor use only / 20 to 90% non-condensing / 2,000m AMSL (Operational) 8,000m AMSL (Storage) Above Mean Sea Level Control & Monitoring Local: HMI, capacitive touch screen Remote: Ethernet via RJ45, 10BaseT/100 BaseTx. ETL TCP/IP, SNMPv2/3, HTTPS & built-in web server.HMI and CPU field replaceable.MTTR 20 minutes (15 minutes to retrieve spare part and 5 mins to replace). Applies to LRUs only and assumed in-house stock. AC Input/Consumption 85-264Vac 50/60Hz / 275W max. consumption at steady state PSU Redundancy Dual redundant and alarmed. Diode OR. Hot swappable. Input & Output Ports Dependant upon module fitted

Alto L-band Redundant Amplifier Module with low noise, high linearity, variable gain and slope control ALT-G1R-S3-101 is an L-band hot swap low noise & high linearity redundant amplifier, with variable gain and slope control designed to fit into the 1U Genus chassis. The 1U redundancy chassis has the capacity for 1+1. 2+1 and 4+2 hot-swap module configurations. Chassis Specification Dimensions/Weight/Colour 1U high x 550mm deep x 19″ wide / Capacity 17 module slots. Note: Actual modules may require >1 slot. Refer to required module spec table. Temperature Operating: 0˚C to +45˚C Storage: -20˚C to +75˚C Location/Humidity/Altitude Indoor use only / 20 to 90% non-condensing / 2,000m AMSL (Operational) 8,000m AMSL (Storage) Above Mean Sea Level Control & Monitoring Local: HMI, capacitive touch screen Remote: Ethernet via RJ45, 10BaseT/100 BaseTx. ETL TCP/IP, SNMPv2/3, HTTPS & built-in web server. HMI and CPU field replaceable. MTTR 20 minutes (15 minutes to retrieve spare part and 5 mins to replace). Applies to LRUs only and assumed in-house stock. AC Input/Consumption 85-264Vac 50/60Hz / 275W max. consumption at steady state PSU Redundancy Dual redundant and alarmed. Diode OR. Hot swappable. Input & Output Ports Dependant upon module fitted

The broadband hot swap variable attenuation module is designed to work in the Genus 1U chassis series, operating over 500 to 6000MHz. The module has -5 to –55dB variable gain range, and the chassis has the capacity to house up to 16 amplifier modules. Other modules types are also available, these can be mixed and housed in the Genus chassis. Chassis Specification Dimensions/Weight/Colour 1U high x 550mm deep x 19″ wide / Capacity 17 module slots. Note: Actual modules may require >1 slot. Refer to required module spec table. Temperature Operating: 0˚C to +45˚C Storage: -20˚C to +75˚C Location/Humidity/Altitude Indoor use only / 20 to 90% non-condensing / 2,000m AMSL (Operational) 8,000m AMSL (Storage) Above Mean Sea Level Control & Monitoring Local: HMI, capacitive touch screen Remote: Ethernet via RJ45, 10BaseT/100 BaseTx. ETL TCP/IP, SNMPv2/3, HTTPS & built-in web server. HMI and CPU field replaceable. MTTR 20 minutes (15 minutes to retrieve spare part and 5 mins to replace). Applies to LRUs only and assumed in-house stock. AC Input/Consumption 85-264Vac 50/60Hz / 275W max. consumption at steady state PSU Redundancy Dual redundant and alarmed. Diode OR. Hot swappable. Input & Output Ports Dependant upon module fitted

Alto C-band Smart Amplifier Module with low noise, high linearity, and variable gain The C-Band low noise amplifier module is designed to work in the Genus 1U chassis series, operating over 850-4200 MHz. The module has low noise, high linearity, and +38 to 0 dB variable gain. The chassis has the capacity for up to 16 amplifier modules, or can house a mixture of other hot-swap module types. Chassis Specification Dimensions/Weight/Colour 1U high x 550mm deep x 19″ wide / Capacity 17 module slots. Note: Actual modules may require >1 slot. Refer to required module spec table. Temperature Operating: 0˚C to +45˚C Storage: -20˚C to +75˚C Location/Humidity/Altitude Indoor use only / 20 to 90% non-condensing / 2,000m AMSL (Operational) 8,000m AMSL (Storage) Above Mean Sea Level Control & Monitoring Local: HMI, capacitive touch screen Remote: Ethernet via RJ45, 10BaseT/100 BaseTx. ETL TCP/IP, SNMPv2/3, HTTPS & built-in web server. HMI and CPU field replaceable. MTTR 20 minutes (15 minutes to retrieve spare part and 5 mins to replace). Applies to LRUs only and assumed in-house stock. AC Input/Consumption 85-264Vac 50/60Hz / 275W max. consumption at steady state PSU Redundancy Dual redundant and alarmed. Diode OR. Hot swappable. Input & Output Ports Dependant upon module fitted

Alto Extended L-band Smart Amplifier Module with low noise, high linearity, and variable gain The extended L-Band low noise amplifier module is designed to work in the Genus 1U chassis series, operating over 850-2450 MHz. The module has low noise, high linearity, +45 to -4 dB variable gain with variable slope control. The chassis has the capacity for up to 16 amplifier modules, or can house a mixture of other hot-swap module types. Chassis Specification Dimensions/Weight/Colour 1U high x 550mm deep x 19″ wide / Capacity 17 module slots. Note: Actual modules may require >1 slot. Refer to required module spec table. Temperature Operating: 0˚C to +45˚C Storage: -20˚C to +75˚C Location/Humidity/Altitude Indoor use only / 20 to 90% non-condensing / 2,000m AMSL (Operational) 8,000m AMSL (Storage) Above Mean Sea Level Control & Monitoring Local: HMI, capacitive touch screen Remote: Ethernet via RJ45, 10BaseT/100 BaseTx. ETL TCP/IP, SNMPv2/3, HTTPS & built-in web server. HMI and CPU field replaceable. MTTR 20 minutes (15 minutes to retrieve spare part and 5 mins to replace). Applies to LRUs only and assumed in-house stock. AC Input/Consumption 85-264Vac 50/60Hz / 275W max. consumption at steady state PSU Redundancy Dual redundant and alarmed. Diode OR. Hot swappable. Input & Output Ports Dependant upon module fitted

Alto Extended L-band Smart Amplifier Module with low noise, high linearity, and variable gain The S-Band low noise amplifier module is designed to work in the Genus 1U chassis series, operating over 850-2450 MHz. The module has low noise, high linearity, +38 to 0 dB variable gain with variable slope control. The chassis has the capacity for up to 16 amplifier modules, or can house a mixture of other hot-swap module types. Chassis Specification Dimensions/Weight/Colour 1U high x 550mm deep x 19″ wide / Capacity 17 module slots. Note: Actual modules may require >1 slot. Refer to required module spec table. Temperature Operating: 0˚C to +45˚C Storage: -20˚C to +75˚C Location/Humidity/Altitude Indoor use only / 20 to 90% non-condensing / 2,000m AMSL (Operational) 8,000m AMSL (Storage) Above Mean Sea Level Control & Monitoring Local: HMI, capacitive touch screen Remote: Ethernet via RJ45, 10BaseT/100 BaseTx. ETL TCP/IP, SNMPv2/3, HTTPS & built-in web server. HMI and CPU field replaceable. MTTR 20 minutes (15 minutes to retrieve spare part and 5 mins to replace). Applies to LRUs only and assumed in-house stock. AC Input/Consumption 85-264Vac 50/60Hz / 275W max. consumption at steady state PSU Redundancy Dual redundant and alarmed. Diode OR. Hot swappable. Input & Output Ports Dependant upon module fitted